塔羅克文翻譯 //#define ENDSTOPPULLUP_XMIN
1.啟用smart control節制板
2.點竄了待機畫面的顯示文字...
//#define USE_XMAX_PLUG
#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
//============================== Endstop Settings ===========================
#endif
再麻煩大師了....
華頓翻譯公司很驚惶(利用Auto Home)
// Specify here all the endstop connectors that are connected to any endstop or probe.
#define ENDSTOPPULLUPS
// Disable ENDSTOPPULLUPS to set pullups individually
完全從鋁擠型到...螺桿光桿等起頭組....故本來是沒有廠商賜與合適的程式
// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
極限接法以下
1：極限接為兩線式，接NO與COM，ramps那邊是接S與(正負都有試過)，但仍是一樣的奇異動作..
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
以下附上極限的設定
#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
#define USE_YMIN_PLUG
目前利用的是marlin 1.1.x，從官方抓的
//#define ENDSTOPPULLUP_YMAX
//===========================================================================
#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
#define USE_ZMIN_PLUG
主要點竄了
組裝好後測試Move AXIS時都可正常，旋鈕往+的處所加各軸向都正常運作
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
//#define USE_ZMAX_PLUG
//#define ENDSTOPPULLUP_YMIN
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
//#define ENDSTOPPULLUP_ZMIN
//#define USE_YMAX_PLUG
// @section homing
城市Z軸往上升(約3CM)，X軸往右移(約1CM)，Y軸撤退退卻(約1CM)，如許的動作重複兩輪
//#define ENDSTOPPULLUP_ZMAX
//===========================================================================
想請問設定擋那邊有無設定錯誤呢？
//#define ENDSTOPPULLUP_XMAX
// Specify here all the endstop connectors that are connected to any endstop or probe.
#define ENDSTOPPULLUPS
// Disable ENDSTOPPULLUPS to set pullups individually
完全從鋁擠型到...螺桿光桿等起頭組....故本來是沒有廠商賜與合適的程式
// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
極限接法以下
1：極限接為兩線式，接NO與COM，ramps那邊是接S與(正負都有試過)，但仍是一樣的奇異動作..
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
以下附上極限的設定
#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
#define USE_YMIN_PLUG
目前利用的是marlin 1.1.x，從官方抓的
//#define ENDSTOPPULLUP_YMAX
//===========================================================================
#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
#define USE_ZMIN_PLUG
主要點竄了
組裝好後測試Move AXIS時都可正常，旋鈕往+的處所加各軸向都正常運作
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
//#define USE_ZMAX_PLUG
//#define ENDSTOPPULLUP_YMIN
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
//#define ENDSTOPPULLUP_ZMIN
//#define USE_YMAX_PLUG
// @section homing
城市Z軸往上升(約3CM)，X軸往右移(約1CM)，Y軸撤退退卻(約1CM)，如許的動作重複兩輪
//#define ENDSTOPPULLUP_ZMAX
//===========================================================================
想請問設定擋那邊有無設定錯誤呢？
//#define ENDSTOPPULLUP_XMAX
各位好，小弟比來 "自組"了一台3D印表機
#define USE_XMIN_PLUG
一般回歸原點不是都邑以撞到極限為主嗎？ 可是感覺像是純潔做軸向活動，並且有沒有撞到極限都不會停
#if DISABLED(ENDSTOPPULLUPS)
// Almost all printers will be using one per axis. Probes will use one or more of the
另外做了些點竄例如啟用A4988的driver等等
//#define ENDSTOPPULLUP_ZMIN_PROBE
#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
以下文章來自: https://www.mobile01.com/topicdetail.php?f=368&t=5568884&p=1有關各國語文翻譯公證的問題歡迎諮詢華頓翻譯公司02-77260932
#define USE_XMIN_PLUG
一般回歸原點不是都邑以撞到極限為主嗎？ 可是感覺像是純潔做軸向活動，並且有沒有撞到極限都不會停
#if DISABLED(ENDSTOPPULLUPS)
// Almost all printers will be using one per axis. Probes will use one or more of the
另外做了些點竄例如啟用A4988的driver等等
//#define ENDSTOPPULLUP_ZMIN_PROBE
#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
以下文章來自: https://www.mobile01.com/topicdetail.php?f=368&t=5568884&p=1有關各國語文翻譯公證的問題歡迎諮詢華頓翻譯公司02-77260932
文章標籤
全站熱搜
